INNOVV Power Hub1 Install on BMW R1200 GS

I got INNOVV Power Hub 1 to power extra accessories like phones and my two GoPros. It gives you 5 circuits switched 12 volts with a 5 amps fuse per circuit. The fuse can be replaced per your need, Max 15A is for a single circuit, Max 40A is for total 5 circuits.  I liked this because it’s water and dust proof plus it’s very cheap. The full details can be found here http://www.innovv.com/innovv-power-hub1-cjxt
 
The Power Hub 1    The size    The Leads, The lead to the battery were far too short so I needed to buy extra wire to lengthen the cables. I also added superseal connectors on the four of the leads and a SAE connector on the last one.You get a single ground lead and I tied all 5 grounds to this single lead.  I used the rear tail light feed for the trigger wire.      The install,   The unit fits absolutely perfectly under the tail section on my 2016 BMW R1200GS. 

Motorcycle Crash and Get Recorded

Mike had install INNOVV K1 Motorcycle Black Box on his Kawasaki Z1000 half year before as below, INNOVV motorcycle camera DVR in pelican 1040 box Few days ago, Mike sent other message, I wanted to check back in with you. Your camera system saved me and the accident was totally the other drivers fault. Some one did U-turn in front of me while on the bike, which is now totaled…  I will start posting in the forums for you. I’m more than happy to do that for you. The k1 system has more than paid for itself by recording my accident on the bike.I doubt the police would have believed my story if I wasn’t able to show them the video at the scene of the accident. Mike said.  It is lucky that the accident got recorded that helps to verify what is wrong indeed, and that strengthens our conviction that the motorcycle cameras we design and develop is to protect riding and create fun. 

Motorcycle Black Box Installed on BMW K1300S

Had been looking for a black box to install on my BMW K1300S for a while, and Kendall, one of friends show me INNOVV K1 2 Channel motorcycle recording system installed on his bike. I should say that was what in my mind, and purchased one set from INNOVV website and got it within a week. The first class delivery service as Kendall mentioned.  I really like its features, that no body can see the cameras installed in front and rear, and you do not worry about battery and SD card get fulfilled.   The front camera. The rear camera  The DVR,   

Installation of INNOVV K1 Motorcycle Camera on a BMW R1200RT Iconic

I had INNOVV K1 motorcycle camera installed on my previous bike (BMW R1200RT) and swapped them to my new bike in November 2016, the only difference was that INNOVV kindly supplied me with a waterproof lens cover for each camera. Having previously run with the cameras in the same locations on the bike for 6 months, I knew they would work well when I swapped them over. The new bike I installed them on is a 2016 BMW R1200RT Iconic (limited edition 100th anniversary model).  Front setup:I made a custom bracket out of  Aluminium Flat Bar (easily obtainable from a well known auction site), and simply bent the ends to form the exact shape to slide into the front of the fairing. I had intended to hold it in place with the two screws already in the fairing (and drilled two holes in readiness), but I found that the fit was so snug that all I needed was two 3m double sided sticky pads to easily hold it securely in place.  After riding with it for 6 months previously, it never moved once. The camera is suspended from the bracket by use of an Anti-Vibration Rubber Damper Dampening Ball, Bar (easily obtainable from a well known auction site), with a small metal tube inside to provide a level of regularity without losing the damping effect.  The camera cable is fed up through the fairing and over the engine, past the battery side and into the space under the front seat where the VCR is located. I wrapped the cable in flame retardant sheathing for added safety. Rear Setup:The rear was slightly easier. I used an M10 Grey Pivot Bracket Standoff U Steel Metal Fixing (easily obtainable from a well known auction site), and drilled a small hole in the rear rack to mount it. Fixing was by use of INNOVV supplied screws.The cable is then simply routed under the rear seat to the DVR.   DVR positioning:Housed in the left side panel, accessible via under the riders seat.   Power connection:On my previous bike I installed a PDM60 Power Distribution Module and used that to feed the DVR. I took the rear 12v din socket cable under the rear seat as a trigger for the ignition. This was an elegant solution and worked perfectly, the unit auto switching off any a few seconds from ignition turning off. It did however require slightly extra work installing the PDM and tapping into the ignition trigger wire. This time, rather than install the PDM (as I don’t need to feed lots of accessories), I went for the Optimate 90 degree waterproof DIN plug with 2 USB outlets and plugged it into the rear 12v din socket on the bike. This unit fits perfectly on this RT and provides a very neat and simple solution, with the added bonus that it is hidden from view and looks like part of the original bike setup. Powering the DVR is then dead easy; simply plug in the USB cable.   The bike powers down the rear socket when the ignition is switched off, but the Optimate unit also has a protective circuit in it that does the same if your bike doesn’t automatically switch off power when the ignition is turned off. So double protection. I didn’t install GPS or remote switch. 

INNOVV K1 Motorcycle Camera For Riding Assessment

I’m a motorcycle instructor, working in Christchurch, New Zealand.  I do riding assessments on riders who are doing licence tests. I’m primarily interested in recording a riders performance so it can be used to support my assessments, It might help solve some arguments.  I’ve just fitted INNOVV K1 Motorcycle camera to my BMW R1200RT 2013. I’d like a set of instructions as to all the settings available for the unit.        

INNOVV K1 Motorcycle Dashcam installed on NC750XD

My bike is a 2015 Honda NC750XD, and just finished INNOVV K1 motorcycle dashcam install.  I attached some pictures I made yesterday. The recording unit is placed inside the front trunk, under the lid originally holding the manuals. From a distance, you can not notice there is a camera.    The close look,   The rear camra  The close look,